Browse Topic: Titanium alloys

Items (2,169)

FITTING, TEE, INTERNAL STRAIGHT THREAD PORT

AS5192F (Current)

7/22/2026

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Clamp Assembly, Saddle Type, Cushioned, General Specification For

AS85449B (Current)

7/13/2026

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Tolerances Titanium and Titanium Alloy Extruded Bars, Rods, and Shapes

AMS2245D (Current)

12/9/2025

This specification covers established manufacturing tolerances applicable to titanium and titanium alloy extruded bars, rods, and shapes. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range.

AMS G Titanium and Refractory Metals Committee

Steel, Corrosion Resistant, Sheet, Strip, and Foil, 19Cr - 9.5Ni (304), Cold Rolled, 125 ksi (862 MPa) Tensile Strength

AMS5501G (Current)

12/8/2025

This specification covers a corrosion-resistant steel in the form of sheet, strip, and foil 0.005 inch (0.13 mm) and over in nominal thickness (see 8.4).

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion-Resistant, Sheet and Strip, 19Cr - 9.2Ni (304), Cold Rolled, Full Hard, 185 ksi (1276 MPa) Tensile Strength

AMS5913D (Current)

11/25/2025

This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness (see 8.6).

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion-Resistant, Sheet and Strip, 19Cr - 9.2Ni (304), Cold Rolled, 3/4 Hard, 175 ksi (1207 MPa) Tensile Strength

AMS5912D (Current)

11/25/2025

This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness (see 8.6).

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion-Resistant, Sheet and Strip, 19Cr - 9.2Ni (304), Cold Rolled, 1/2 Hard, 150 ksi (1034 MPa) Tensile Strength

AMS5911D (Historical)

11/25/2025

This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness (see 8.6).

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion-Resistant, Sheet and Strip, 18Cr - 8Ni (301), Cold Rolled, 3/4 Hard, 175 ksi (1207 MPa) Tensile Strength

AMS5902E (Historical)

11/25/2025

This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005-inch (0.13-mm) in nominal thickness (see 8.6).

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion Resistant, Bars and Wire, 19Cr - 10Ni (304), High Yield Strength, Solution Heat Treated and Cold Worked

AMS5857E (Historical)

11/25/2025

This specification covers a corrosion-resistant steel in the form of cold-worked bars and wire up to 1.750 inch (44.45 mm) inclusive, in nominal diameter or least distance between parallel sides (see 8.4).

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion Resistant, Bars, Wire, and Forgings 5.8Mn - 17Cr - 5.8Ni - 2.0Cu - 0.26S Free Machining, Solution Heat Treated

AMS5762H (Current)

11/25/2025

This specification covers a free-machining, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion Resistant, Bars and Wire, 18Cr - 9Ni (303F), Free Machining, High Yield Strength, Solution Heat Treated and Cold Worked

AMS5738F (Current)

11/25/2025

This specification covers a free-machining, corrosion-resistant steel in the form of cold-worked bars and wire up to 1.750 inches (44.45 mm) inclusive, in nominal diameter or least distance between parallel sides (see 8.5).

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion-Resistant, Bars and Forgings 0.14S - 18Cr - 9.5Ni - 0.50Mo - 0.80Al (303MA) Free-Machining; Swaging or Upsetting Solution Heat Treated

AMS5638H (Current)

11/25/2025

This specification covers a free-machining, corrosion-resistant steel in the form of bars, forgings, and forging stock.

AMS F Corrosion Heat Resistant Alloys Committee

Iron-Nickel Alloy, Strip, 49Fe - 5.3Cr - 42Ni - 2.5Ti - 0.55Al, Solution Heat Treated, Cold Rolled, 10% Reduction

AMS5223H (Current)

11/25/2025

This specification covers an iron-nickel alloy in the form of strip 0.020 to 0.1874 inch (0.51 to 4.760 mm), inclusive, in nominal thickness (see 8.6).

AMS F Corrosion Heat Resistant Alloys Committee

Iron-Nickel Alloy Strip, 49Fe - 5.3Cr - 42Ni - 2.5Ti - 0.55Al, Solution Heat Treated

AMS5221G (Current)

11/25/2025

This specification covers an iron-nickel alloy in the form of strip 0.020 to 0.250 inch (0.51 to 6.35 mm) inclusive, in thickness (see 8.8).

AMS F Corrosion Heat Resistant Alloys Committee

Test Publishing Document

ARP090824B (Current)

10/13/2025

Test Publishing Document6667

A-6 Aerospace Actuation, Control and Fluid Power Systems

Electron-Beam Welding For Fatigue Critical Applications

AMS2680D (Current)

9/30/2025

This specification defines the procedures and requirements for joining metals and alloys using the electron beam welding process.

AMS B Finishes Processes and Fluids Committee

Liquid Runway Deicing/Anti-icing Product

AMS1435E (Current)

3/12/2024

This specification covers runway deicing and anti-icing products in the form of a liquid. Unless otherwise stated, all specifications referenced herein are latest (current) revision.

G-12RDP Runway Deicing Product Committee

Aerospace Fluid System Standards, Metric, National and International

AIR2000F (Current)

3/25/2022

The purpose of this aerospace information report is to provide a listing of national and international metric standards for use in aerospace fluid systems with their equivalent SAE inch, International ISO, and European AECMA standards.

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Inspection, Ultrasonic Product Over 0.5 Inch (12.7 mm) Thick

AMS2630E (Current)

11/9/2021

This specification covers procedures for ultrasonic inspection, by pulse-echo procedures, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.5 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness.

AMS K Non Destructive Methods and Processes Committee

Aluminum Alloy Powder 7.0Si - 0.55Mg - 0.12Ti

AMS7020 (Current)

11/9/2021

This specification covers an aluminum alloy in the form of pre-alloyed powder.

AMS AM Additive Manufacturing Metals

Structural Examination of Titanium Alloys Etch-Anodize Inspection Procedure

AMS2642F (Current)

11/3/2021

This specification covers a procedure, typically referred to as Blue Etch Anodize, for revealing the macrostructure and microstructure of selected titanium alloys.

AMS B Finishes Processes and Fluids Committee

FITTING, ADAPTER, UNION, FLARED TO BOSS

AS933E (Historical)

10/8/2021

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Tolerances Titanium and Titanium Alloy Extruded Bars, Rods, and Shapes

AMS2245C (Historical)

9/14/2021

AMS G Titanium and Refractory Metals Committee

Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1800 °F (982 °C) Solution Heat Treated

AMS5525L (Current)

9/1/2021

This specification covers a corrosion and heat-resistant steel in the form of sheet, strip, and plate 0.0010 inch (0.025 mm) and above in nominal thickness (see 8.6).

AMS F Corrosion Heat Resistant Alloys Committee

FITTING, ELBOW, 45°, INTERNAL STRAIGHT THREAD PORT

AS5191B (Current)

8/26/2021

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

FITTING ASSEMBLY, UNION, AXIALLY SWAGED, HYDRAULIC 5080 PSI

AS5969G (Current)

8/26/2021

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Fitting, Elbow, 90°, Internal Straight Thread Port

AS5190C (Current)

8/26/2021

SCOPE IS UNAVAILABLE.

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Alloy Verification and Chemical Composition Inspection of Welding Wire

ARP4926B (Current)8/5/2021

This SAE Aerospace Recommended Practice (ARP) covers procedures for welding wire verification and conformance to specification composition.

AMS B Finishes Processes and Fluids Committee

Titanium Ti-5553 (Ti - 5Al - 5Mo - 5V - 3Cr) Powder for Additive Manufacturing

AMS7026 (Current)

7/28/2021

This specification covers a titanium alloy in the form of pre-alloyed powder.

AMS AM Additive Manufacturing Metals

Steel, Corrosion and Heat-Resistant, Sheet, Strip, Foil, and Plate 15Cr - 7.1Ni - 2.5Mo - 1.1Al Solution Heat Treated, Precipitation Hardenable

AMS5520H (Current)

7/23/2021

This specification covers a corrosion and heat-resistant steel in the form of sheet, strip, foil, and plate 0.0015 inch (0.038 mm) and greater in nominal thickness.

AMS F Corrosion Heat Resistant Alloys Committee

Steel, Corrosion-Resistant, Sheet, Strip, and Plate 19Cr - 9.2Ni (SAE 30304) Solution Heat Treated

AMS5513K (Historical)

7/23/2021

This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.

AMS F Corrosion Heat Resistant Alloys Committee

The Chemical Milling Process

ARP1331C (Current)

7/15/2021

This practice provides recommendations concerning the chemical milling of aluminum, magnesium, high temperature nickel alloys, titanium alloys, copper alloys, and specialty alloys.

AMS B Finishes Processes and Fluids Committee

Inspection, Ultrasonic, Wrought Metals, Process for

AMSSTD2154E (Current)

7/15/2021

The purpose of this standard is to provide uniform methods for the ultrasonic inspection of wrought metals and wrought metal products.

AMS K Non Destructive Methods and Processes Committee

Titanium Bars, Wire, Forgings, and Rings Commercially Pure 70 ksi (483 MPa) Yield Strength

AMS4921R (Current)

7/7/2021

This specification covers one grade of commercially pure titanium in the form of bars, wire, forgings, flash welded rings, up to 4.000 inches (101.60 mm), inclusive, in nominal diameter or least distance between parallel sides, and stock for forging or flash welded rings.

AMS G Titanium and Refractory Metals Committee

FITTING, 37° SPHERICAL FLARED, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 45°

AS6094B (Current)

6/28/2021

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

FITTING, 37° SPHERICAL FLARED, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 75°

AS6092B (Current)

6/28/2021

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

FITTING, 37° SPHERICAL FLARED, CONNECTOR, MULTIPLE, FLUID PRESSURE LINE, TEE

AS6095B (Current)

6/28/2021

SCOPE IS UNAVAILABLE.

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

FITTING, 37° SPHERICAL FLARED, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 90°

AS6093B (Current)

6/28/2021

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Aluminum Alloy Powder 4.6Cu - 3.4Ti - 1.4B - 0.75Ag - 0.27Mg

AMS7033 (Current)

6/22/2021

This specification covers an aluminum alloy in the form of pre-alloyed powder.

AMS AM Additive Manufacturing Metals

Ultrasonic Inspection Titanium and Titanium Alloy Bar, Billet and Plate

AMS2631F (Historical)

6/22/2021

This specification covers the procedure for ultrasonic inspection of wrought titanium and titanium alloy products 0.25 inch (6.4 mm) and over in cross-section (thickness) or diameter.

AMS K Non Destructive Methods and Processes Committee

FITTING, BUSHING, PORT, REDUCER

AS5173D (Historical)

6/10/2021

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Titanium Alloy, Sheet, Strip, and Plate 5Al - 2.5Sn Annealed

AMS4910S (Current)

6/10/2021

This specification covers a titanium alloy in the form of sheet, strip, and plate up to 4.000 inches (101.60 mm), inclusive, in thickness.

AMS G Titanium and Refractory Metals Committee

Tube Fittings, Aerospace Fluid Systems, Separable, for 24 Degree Cone, General Specification, Metric (ISO 7169)

MA2005C (Historical)

6/10/2021

This document specifies performance and quality requirements for the qualification and manufacture of 24 degree cone fittings to ensure reliable performance in aircraft hydraulic systems. This document specifies baseline criteria for the design and manufacture of system fittings that are qualification tested on engines. This document covers fittings of temperature types and pressure classes specified in MA2001.

G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies